View source for Slicer3:Module:Fuzzy Surface Creation-Documentation-3.2

[[Documentation|Return to Slicer Documentation]]

===Fuzzy Surface Creation===

__TOC__

== General Information ==

Data sharing became a big issue in the last few years. Unfortunately for research data sharing is a difficult undertaking because of patient privacy protection.
This constricts the exchange of patient secific data between different research groups and faculties.

MRI and CT data itself wouldn't be that delicate since the identification of a patient isn't obvious.
But the rendering of the data into a 3D view reveals a lot of information about the skin and skull structure of a patient and therefore makes a patient easily identifiable.

The aim of this module is therefore to hide as much surface information of the patient as possible but also to keep internal structures untouched.
===Module Type & Category===

Type: CLI

Category: Privacy Protection

===Authors, Collaborators & Contact===
* Author: Bernhard Pflug, University for medical informatics and technology, Tyrol, Austria
* Contact: Bernhard Pflug, bernhard.pflug@gmail.com

===Module Description===

The purpose of this module is to hide as much surface details of a patient as possible. Therefore it adds
an additional surface to the '''front''' of the object in the image depending on different calulated parameters.

As a first step the module detects the object in the image. Subsequent it adds additional data on the detected surface
depending on several calculated parameters. As a result it creates an additional surface on the object which hides skin
and skull details so that patient identification isn't obvious any more.

== Usage ==

This module is a CLI Module for Slicer. It is mainly seperated into two parts:

* '''Preprocessing'''
* '''Fuzzy Surface Creation'''

==== Preprocessing ====
The first step is meant to be the pre-processing step. The aim of this step is to provide a label map defining the human as good as possible. Particulary important for the success of the algorithm is a very good detection of the surface and the reduction of noise outside the human. The Otsu - Threshold - Filter is used as it provides quite good segmentation results on the object in the image and is considerably robust against noise, especially if it is not connected to the object.

The pre-processing task defines the following parameters:

* ''bright objects''
* ''number of histogram bins''
* ''face connected''
* ''minimum object size''

For further information about these parameters check the Otsu - Threhold - Filter in Slicer3.

Second part of the pre-processing is the usage of the Orient Image Filter to adjust the image that the anterior direction of the human is always looking to the top of the image. This guarantees that the fuzzy surface algorithm works always with the front of the patient.

==== Fuzzy Surface Creation ====

The second step is the actual creation of the fuzzy surface. 
Important to mention is that this algorithm works local, so it creates the additional surface for each
voxel without considering the environment! (only exception is the median value which considers all surface values of one row)

[[Image:PrivacyModuleProperties.png|thumb|280px|Privacy Module in Slicer3]]

It defines the following parameters:

* ''Surface value''
** ''Enable surface value''
** ''Surface value divisor''
* ''Middle value''
** ''Enable middle value''
** ''Middle value divisor''
* ''Median value''
** ''Enable median value''
** ''Median value divisor''
* ''Enable overflow cut''
* ''Infiltration depth''
* ''Infilling random range''


* '''''Surface-, Middle-, Median value'''''
:These parameters are calculated and used to compute the height of the added surface. They define the consideration of the calculated value and there aggregation to the final additional height.The parameters serve as divisors, so the lower they are set the more they are considered. The surface parameter defines the distance of a surface point to the border of the image, the middle value the distance from the point to the center of the z-axis and the median value the distance between the point and the median of all surface values of the current slice. Furthermore every value can be en- or disabled by the respective check box.

* '''''Enable overflow cut'''''
:By checking the overflow cut box every value above the created additional surface is set to zero. This improves the fuzzy effect because especially values which are not detected by the Otsu Threhold Preprocessing like especially skin which wouldn't be influenced otherwise can be removed. But this also means that all information above the created surface will be lost.

* '''''Infiltration Depth'''''
:The infiltration depth defines the number of voxels the algorithm goes into the detected surface structure to overlap original voxels with the new created ones. The deeper the algorithm goes into the object the more information will be lost.

* '''''Infilling random range'''''
:For the intensity of the added voxels an average value of the underneath voxels (5 by default) from the surface value is determined. For adding the new surface this value including a random created value is used for intensity estimation. The random range parameter defines the range for the random created value.

===Example===

For the following example an image dataset of a human head was used.

<gallery perrow="1" heights="150" widths="650">
  Image:PrivacyOriginalData2D.png|Original dataset before manipulation
  Image:PrivacyFuzzyData2D.png|dataset after manipulation
</gallery>

After execution of the privacy module there is a additional surface visible on the front of the head surface.

<gallery heights="200" widths="200">
  Image:PrivacyOriginalDataSlice.png|Original
  Image:PrivacyFuzzyDataSlice.png|Manipulated
</gallery>

This example shows the data in the 3D view in slicer before and after the usage of two different parameter settings in the module.

<gallery>
  Image:PrivacyOriginal3DView1.png|3D view before manipulation
  Image:PrivacyManipulated1View1.png|3D view after manipulation
  Image:PrivacyManipulated2View1.png|3D view after another manipulation
</gallery>

From another point of view:

<gallery>
  Image:PrivacyOriginal3DView2.png|3D view before manipulation
  Image:PrivacyManipulated1View2.png|3D view after manipulation
  Image:PrivacyManipulated2View2.png|3D view after another manipulation
</gallery>

== Development ==
This module is splitted into two C++ files:

* '''''itkFuzzySurface'''''
:This class is a subclass of itkImageToImageFilter and handles the fuzzy surface creation. It's a fully functional itk filter and can be embedded in every appropriate itk image processing pipeline. This structure makes the algorithm abstract from it's preprocessing, provides better separation between functional independent parts and offers better maintenance and reusability.

* '''''Privacy'''''
:This file includes the main function and therefore the execution of the module. It first calls the preprocessing steps (Otsu Threshold) and afterwards the fuzzySurfaceFilter. Additionally all required parameters for the algorithms are set.

===Source code & Documentation===

Moreover to this wiki page there is documentation available in the source code. I tried to structure the files as good as possible and also to document any necessary part. I did this especially for people who are not really familiar with ITK, generic programming and Slicer. Therefore the files may seem a little bit overdocumented for sophisticated developers.

== More Information == 

===Acknowledgment===
The development took place in the Surgical Planning Laboratory, Harvard Medical School and Brigham and Women's Hospital, under the supervision of Mr. Steve Pieper Ph.D.